• New generation ultra bright LEDs makes the LD 600 the brightest of Cat Eye's Tail lights with 5 LED's.
• Four mode options allow the LD-600 to switch between flashing, constant, side to side, and random illumination.
• Switchable for constant light or a steady flash. 30 hour run time in flashing mode, 15 hours in steady mode.
• Easily mounts to a seatpost or seat stay with a universal mounting bracket. May be postioned in a horizontal or vertical position.

• Quick release bracket and a 7/8 of an inch to 1 1/4 inches
  (23.5 to 30.5 mm) seatpost/frame tubing hose clamp, included.
• Uses 2 AAA batteries, NOT included.
• Weight is only 37 grams, w/o batteries.
• Dimensions in inches and centimeters.
  LED lamp unit - 5 inches ( 12.0 cm) long by 1.5 inches ( 3.8 cm) in tall by 1.1 inches ( 2.6 cm) wide.

• Allows you to put handlebar mounted accessories above, below or in front of your handlebars. Mounts on your handlebars, stem or even your seatpost. The extension arm pivots 180 degrees.
• Two sizes are available. Both employ a 140 mm (5.6 inches) extension measured from the center of the bar clamp to the center of the horizontal accessory bar.
  The small Swing Grip comes with a 100 mm (4 inches) horizontal accessory bar while the large size has a 130 mm (5.1 inches) horizontal bar.
• Both sizes are available in satin silver or gloss black.
• Fits all road or MTB handlebars from 22mm (7/8 of an inch) to 35mm (1 3/8 of an inch) in diameter. May also be clamped to seatposts and larger frame tubes. Ideal for extra tail lights.

• Both horizontal accessory mounting bars may be adjusted side to side by 20 mm ( 3/4 of an inch). The 100 mm bar will hold two bar mounted accessories while the 130 will hold three.
• The horizontal accessory mounting bar may be rotated 360 degrees in 90 degree increments which makes the Swing Grip ideal for recumbents or non-bicycle applications. The extension bar pivots or swings 180 degrees. It may be locked in any position by simply tightening a 3mm allen bolt.
• Stainless steel clamp band, anodized silver or enameled black, alloy tube and carbon/plastic extension are well made and exceptionally durable.
• Easy to install. Requires a 3 mm allen wrench and a Phillips screwdriver. The allen wrench is included.
• Weighs only 91 or 97 grams.
• Warranty service and help with technical questions is available from the official Minoura USA Service Center in Hayward, California. Call them at (510) 538-8599 or email them at MinouraUSA@ATTGlobal.Net by clicking on the underlined text .
• More product information is also available at the Official Minoura Web Site in Japan.
  Minoura product manuals may be downloaded. They are in Adobe PDF format and require Adobe Acrobat Reader 4.0 or higher to read or print.

• New generation, ultra bright, white single LED. Note that the lense is red or clear; the LED is white. Clear lens NOT pictured.
• A single, bright LED results in exceptionally long battery life.
• Quick release bracket and a Cateye SP-5, 23.5 to 27.2 mm seatpost/frame tubing clamp with two rubber shims, included.
• Uses 3, long life AAA type photo alkaline batteries which are included.
• Switchable for constant light or a steady flash. Astounding 200 hour run time in flashing mode, 100 hours in steady mode!
• Clear housing model gives a "glow in the dark" appearance for higher visibility and safer riding.
• Custom molded, super strong polycarbonate, 180 degree visibility, red or clear lense.
• Weight is only 42 grams, with batteries.
• Dimensions in inches and centimeters.
  LED lamp unit - 3.25 inches ( 8.0 cm) long by 1 inch ( 2.3 cm) tall by 1.75 inches ( 4.8 cm) wide.

• The ONLY rear tail light that combines a flashing LED light with a CPSC reflector for maximum safety. Even if your batteries are dead the reflective lense will bounce back 70% of the light from an oncoming car's headlights.
• New generation ultra bright LEDs. Only 2 clear LEDs are required which results in longer battery life with no loss in visibility.
• Quick release bracket and a 7/8 of an inch to 1 1/4 inches
  (23.5 to 30.5 mm) Cateye SP-6 seatpost/frame tubing clamp with two rubber shims, included.

• Uses 2 N type batteries which are included.
• Switchable for constant light or a steady flash. 100 hour run time in flashing mode, 50 hours in steady mode.
• Clear housing model gives a "glow in the dark" appearance for higher visibility and safer riding.
• Custom molded, super strong, polycarbonate lense.
• Weight is only 75 grams with batteries.
• Dimensions in inches and centimeters.
  LED lamp unit - 2.75 inches ( 7 cm) long by 1.75 inches ( 4.5 cm) in tall by 1.1 inches ( 2.8 cm) wide.

• New generation ultra bright LEDs. Only 3 LEDs are required which results in longer battery life with no loss in visibility.
• Quick release bracket and a 3/4 of an inch to 1 1/2 inches
  (18 to 40 mm) seatpost tubing hose clamp, included.
• Uses 2 AAA batteries, NOT included.
• Switchable for constant light or a steady flash. 100 hour run time in flashing mode, 50 hours in steady mode.
• Four mode options allow the LD-120 III to switch between flashing, constant, side to side, and random illumination.

• Built in clothing/belt clip and the small size of this LED saftey light make it ideal for running, inline skating, motorcycle riding, night skiing, etc.
• Custom molded, super strong, polycarbonate lense.
• Weight is only 55 grams, w/o batteries.
• Dimensions in inches and centimeters.
  LED lamp unit - 3 inches ( 8.0 cm) long by 1.5 inches ( 3.8 cm) in tall by 1.1 inches ( 2.6 cm) wide.

At Branford Bike we want you to be happy and satisfied with everything you purchase from us. We understand that sometimes you will need to return a product because it was not quite what you wanted. You may return anything you purchase from us within 60 days and unused, for an immediate exchange or refund.

Our Secure Order Form is easy to use. Simply fill in the boxes as you would for a traditional paper catalog order form.

Our Secure Order Form opens in a separate window that you may resize and tile behind our online catalog. After filling in your name, address and card information you may leave the order window open. Browse through our catalog and when you wish to purchase an item simply "cut and paste" the part number and description to the appropriate order form boxes.

When you are done shopping, submit your order for error checking, and then for processing. We will email you a confirmation within 10 minutes. Another, more detailed confirmation, will follow when we ship your order.

   
We accept Visa, Discover and MasterCard for payment.
We will NOT charge your card until your order is shipped.

To print this page:
Use your browser's Print command or
press Ctrl + P on Windows, or Command + P on Mac.